Install Vehicle Gateway

Motive Vehicle Gateway needs to be installed and connected to your vehicle before it can track location, log drive time, or run compliance data, so install it before you do anything else with that truck. 

Before you begin

  • Confirm your vehicle's make, model, and year. 
  • Install the Motive Fleet App on your phone and log in with your Fleet Admin, Fleet Manager, or Installer credentials. It walks you through the install and verifies it for you.
  • Park safely, engage the parking brake, and turn the engine off of your vehicle before you start the installation process.

Cable-specific installation 

  • Identify the diagnostic port type (J1939, RP1226, OBD-II, 6-pin, or hardwired) of your vehicle.
  • Have your Vehicle Gateway kit and the matching cable on hand. Check the label on the cable against your port type. If you are not sure which cable you need, refer to this article.

Assigning the Vehicle Gateway to a vehicle

  1. Log in to the Fleet App and tap Devices.
  2. Tap Install Vehicle Gateway.
  1. Scan the serial number barcode of the new Vehicle Gateway. It can be found on the upper right corner of the sticker on the back of the Vehicle Gateway or on the packaging box in which the device arrived.
  1. Tap Enter VIN Manually to enter the VIN of the vehicle yourself or scan it.
  2. If you tap Enter VIN Manually, enter the VIN.
  3. Tap Next.
  1. If you previously decided to scan the VIN, tap Continue once it has been scanned.
  2. Check that the vehicle details created based on VIN data, like Make/Model/Year/Fuel Type, are correct. Tap Confirm.
  3. Give the vehicle a unique ID consistent with your fleet naming convention. Note this cannot be changed once it has been assigned. 
  4. Once the vehicle details are confirmed, your vehicle will be added to your fleet, and your selected Vehicle Gateway will be assigned to this vehicle. 
  5. Once assigned, tap Continue.

Mount and test the Vehicle Gateway

  1. Once the Vehicle Gateway is assigned, confirm you have the correct cable for installation by checking the label on the cable. Tap Next.
Note: For supported heavy-duty vehicles with an RP1226 connector, use the RP1226 connection instead of the standard diagnostic port. Using the standard port may affect your vehicle warranty.
iphone16pro-full-2 (60).png
  1. Choose a recommended temporary location for mounting the Vehicle Gateway. Tap Next.
iphone16pro-full-2 (61).png
  1. Place the Vehicle Gateway at the selected location and connect the 15-pin connector to it, ensuring the other end connects to your vehicle’s diagnostic port without removing the adhesive backing. Tap Next after performing each step.
  2. Avoid deep under-dash installations, as hiding the device under heavy metal or far from the windshield degrades GPS signal quality and can lead to missed geofence alerts.
Note: For heavy-duty vehicles, mount the Vehicle Gateway near the windshield / upper dash area with the Motive logo facing up, away from vents and electrical components, and at least 12 inches away from metal components.
iphone16pro-full-2 (62).png
  1. The left-side LED will turn green, indicating a strong cellular/GPS connection. Tap LED behavior verified.
iphone16pro-full-2 (63).png
  1. Ensure Bluetooth is enabled and that you are near the Vehicle Gateway. Once ready, tap Begin Test.
iphone16pro-full-2 (64).png
  1. The test may take up to 2 minutes to complete. A notification will confirm whether the test has passed or failed.

If the pre-install test has passed: 

  1. All the tests have been verified, and you can proceed by tapping Next.
iphone16pro-full-2 (65).png

If the pre-install test has failed:

  1. If the test fails, review the errors and refer to the troubleshooting instructions in the Learn More link before testing again.
  2. Run the test again to check for success.
iphone16pro-full-2 (66).png
  1. If you choose to skip the test, complete the installation details, but note that the installation is marked as incomplete even if you complete the physical installation. Tap Continue anyway.
iphone16pro-full-2 (67).png
  1. Tap I understand to proceed.
iphone16pro-full-2 (68).png

Mounting and installing the Vehicle Gateway

  1. Permanently mount the Vehicle Gateway at the desired location and tap Next.

    iphone16pro-full-2 (69).png
  2. After mounting, enter the installation details, such as the Odometer reading, Engine hours, Power Source, and Installation photos, and tap Next. Peel off the adhesive backing and securely position the device using the provided zip ties.
iphone16pro-full-2 (70).png
iphone16pro-full-2 (71).png
  1. The Vehicle Gateway installation is complete. Tap View this vehicle to see the vehicle profile with updated location information.
iphone16pro-full-2 (72).png
  1. The latest location information can be found on the newly installed Vehicle Gateway.
iphone16pro-full-2 (73).png

How to know it worked: The vehicle's profile shows updated location and device data. This can take a few minutes depending on cellular signal at your install location.

Next steps

  • Confirm Vehicle Gateway data is populating in the Fleet Dashboard. Fleet admins can review Vehicle telematics health, data, and follow a vehicle in real-time through the Fleet Dashboard. 
  • Pair a driver's mobile device to the installed Vehicle Gateway so they can start recording their driver time and track their hours of service. 
Was this article helpful?

Share this with others