Asset Gateway Mini needs to be assigned to an asset and activated before it can start reporting location. The cable-powered Asset Gateway Mini requires a matching cable for your asset (3-wire, 8-wire, or ABS).
Before you begin
- Locate the device's serial number on the label on the front of the device or the shipping box.
- Have the pinhole reset tool that came in the box handy.
Selecting and pairing an Asset Gateway Mini with an asset in the Fleet App
- Log in to the Fleet App and go to Devices.
- Scroll down to the Asset Gateway section and tap Install Asset Gateway.
- Select your Asset Gateway Mini from the list or enter its serial number in the search bar to find and select it.
- If your selected Asset Gateway Mini is not assigned to any asset at the moment, a pop-up appears to confirm that it is ready to be assigned.
- Tap Continue.
| Note: For already assigned devices, you have to unassign the Asset Gateway Mini from the previous asset to be able to assign it to another asset. |
- Select your Asset from the list or enter its Asset ID in the search bar to find and pair it with the selected Asset Gateway Mini.
- View the Asset Details and tap Confirm.
- A loading pop-up appears while the Asset Gateway Mini is being assigned to the selected asset.
- Once the Asset Gateway Mini is assigned to the selected asset, a confirmation pop-up appears.
- Tap Continue.
Mounting the cable-powered Asset Gateway Mini
- Tap Install with cable to install any cable-powered Asset Gateway Mini.
- Select your desired cable from the given options: 3-wire cable, 8-wire cable, and ABS cable.
- Select your preferred Unpowered check-in rate and tap Confirm.
- Tap Start guided installation to follow step-by-step instructions for installation.
| Note: Skipping guided installation allows installers who are aware of the steps to skip past all the steps and simply connect the Asset Gateway Mini and run tests if necessary. |
Guided installation of cable-powered Asset Gateway Mini
- When you are prepared to mount the device, tap Next.
- Place or hold the device in the intended location and tap AG in chosen location.
- To test cellular and GPS connectivity, use the provided pin to press the pinhole reset button on the side of your device, which will send a testing signal.
- Once your LED light flashes blue and the device is switched on, tap Light flashed blue.
|
Note: Tap LED did not flash blue if your LED light is white, orange, or red. You will be prompted to confirm the color of your LED light. Select the color of your LED light and follow the given instructions.
|
- A loading pop-up appears while the testing is in progress.
- Once the test is complete, a confirmation pop-up appears with green tickmarks to verify that GPS and LTE signals are strong.
- Tap Continue.
| Note: If your test results show weak or failed signals for GPS and/or LTE, we recommend checking how your device is installed to ensure it is positioned with a clear view of the sky. A weak cellular signal may affect the device’s performance. |
- Follow the given instructions to mount the Asset Gateway in your chosen location.
- Once done, tap AG is mounted.
Installing and testing cable-powered Asset Gateway Mini
Installing and testing the Asset Gateway Mini with ABS cable
- Follow the steps given above for Selecting and pairing an Asset Gateway Mini with an asset and Mounting the cable-powered AG Mini.
- Follow the given instructions to connect wires to the Asset Gateway.
- Once done, tap AG is connected.
- Follow the given instructions to connect your Asset Gateway to the ABS Module.
- Once done, tap Connected to ABS Module.
- To test power, follow the given instructions to tether the asset to the vehicle before turning on the ignition.
- With the provided pin, press the pinhole reset button on the side of your device to send a testing signal.
- Tap the Reset button pressed.
- A loading pop-up appears while the testing is in progress.
- Once the test is complete, a confirmation pop-up appears with a green tickmark for Power verified.
- Tap Continue.
- Once the installation is complete, view the asset paired with your Asset Gateway or install more devices.
Installing and testing the Asset Gateway Mini with a 3-Wire cable
- Follow the steps given above for Selecting and pairing an Asset Gateway Mini with an asset and Mounting the cable-powered AG Mini.
- Turn the engine off. When you are prepared to connect wires, tap Next.
- Follow the given instructions to connect wires to the Asset Gateway.
- Once done, tap AG is connected.
- Follow the given instructions to connect the ground wire.
- Once done, tap Ground wire connected.
- Follow the given instructions to connect the ground wire.
- Once done, tap Red wire connected.
- Follow the given instructions to send a testing signal.
| Note: If you are connected to constant power, press the reset button. If you are connected to intermittent power, tether your asset to a vehicle and turn the ignition on before pressing the reset button on the side of the device to send a test signal. |
- Tap Reset button pressed.
- A loading pop-up appears while the testing is in progress.
- Once the test is complete, a confirmation pop-up appears with a green tickmark for Power verified.
- Tap Continue.
- Tap Step up AUX line to configure the AUX line for monitoring your asset’s ignition or tracking its engine hours. You can also configure the AUX line to monitor other functions that provide voltage.
- Name the AUX line and configure its voltage logic.
- Once done, tap Next.
- Follow the given instructions to test the main motor.
- Tap Reset button pressed.
- A loading pop-up appears while the testing is in progress.
- Once the test is complete, a confirmation pop-up appears with a green tick mark for verification.
- Tap Continue.
- Once the installation is complete, you can view the asset paired with your Asset Gateway or install more devices.
Installing and testing the Asset Gateway Mini with an 8-wire cable
- Follow the steps given above for Selecting and pairing an Asset Gateway Mini with an asset and Mounting the cable-powered AG Mini.
- Turn the engine off. When you are prepared to connect wires, tap Next.
- Follow the given instructions to connect wires to the Asset Gateway.
- Once done, tap AG is connected.
- Follow the given instructions to connect the ground wire.
- Once done, tap Ground wire connected.
- Follow the given instructions to connect the ground wire.
- Once done, tap Red wire connected.
- Follow the given instructions to send a testing signal.
| Note: If you are connected to constant power, press the reset button. If you are connected to intermittent power, tether your asset to a vehicle and turn the ignition on before pressing the reset button on the side of the device to send a test signal. |
- Tap Reset button pressed.
- A loading pop-up appears while the testing is in progress.
- Once the test is complete, a confirmation pop-up appears with a green tick mark for Power verified.
- Tap Continue.
- Tap Step up AUX lines to configure the AUX lines for monitoring functions that provide voltage, such as monitoring ignition, which allows tracking of the asset’s engine hours.
- Mark the checkboxes for the AUX lines you want to configure and connect to your asset.
- Once done, tap Confirm.
- Name the green AUX line and configure its voltage logic.
- Once done, tap Next.
- Follow the given instructions to test the main motor.
- Tap Reset button pressed.
- A loading pop-up appears while the testing is in progress.
- Once the test is complete, a confirmation pop-up appears with a green tick mark for verification.
- Tap Continue.
- Tap Continue and follow steps 17-23 from above to configure, connect, and test the orange AUX line to any voltage source on your asset.
- Tap Continue and follow steps 17-23 from above to configure, connect, and test the brown AUX line to any voltage source on your asset.
- Once the installation is complete, you can view the asset paired with your Asset Gateway or install more devices.
How to know it worked: The app shows green checkmarks for both GPS/LTE and power verification.
If it doesn't:
- A weak or failed signal means the mounting spot does not have a clear view of the sky or is blocked by metal. Reposition and retest before mounting permanently.
- A failed power test usually means a loose or reversed wire connection. Recheck power, ground, and ignition wiring against the in-app diagram.
Next steps
- Confirm the cable-powered Asset Gateway Mini's data is populating in the Fleet Dashboard. Go to the asset's page in the Fleet App or Fleet Dashboard. The asset's location appears on the Live page. This can take 15-30 minutes for cable-powered devices or up to 48 hours for battery-powered devices on their first fix. See Fleet View Live Tracking.
Was this article helpful?
Share this with others